HEAT ACTIVATED HOT MELT POWDER ADHESIVES

Lancer's hot melt powders are heat activated adhesives that can be used for virtually any application requiring a heat applied system. When applied to transfers this greatly increases the washability of the product and the adhesion to garments made of synthetic fabric.

AVAILABLE SIZES: 1.1lbs (500g), 6.6lbs (3Kg) and 22lbs (10Kg)

COMPONENTS / APPLICATION FOR SUPERHOLD POWDERS

H-1: A medium grind hot melt powder. Melts quickly - ideal where fast application is required i.e. plastisol or water based puff transfers.

H-10: Superhold, very fine grind hot melt powder. Ideal for extremely fine detailed transfers. Fine lines won't get lost or pulled off.

H-15: Extremely coarse grind hot melt powder. Used primarily for covering large areas such as crests. Large particle size makes this powder easy to handle, providing a good bond for heat seal crests.

H-23: Multi-grind formula ideal for flock transfers.

Plastisol Transfers: Sprinkle Superhold Powder onto the wet ink, shake off excess and heat cure. (Use H-1 or H-10)

Crests: Sprinkle Superhold Powder onto back of crest and heat cure until adhesive is melted. (Use H-15 or H-10)

Flock Transfers: Sprinkle Superhold Powder onto wet adhesive, shake off excess and air dry. After drying brush off excess and heat cure. (Use H-23)

Puff Transfers - Plastisol or Water Based: Sprinkle Superhold Powder onto wet ink, shake off excess and heat cure at low temperature or if water based let air dry. (Use H-1)

AVAILABLE COLORS (.008 x .008): Electric Green (laser), Fire & Ice (laser), Gold Dust (laser), Gold Glitter, Ice Blue (laser), Ice Wine (laser), Silver Glitter, Techno Silver (laser), Crystallina

AVAILABLE COLORS (.004 x .004): Metallic Silver Sparkle, Metallic Gold Sparkle, Metallic Copper Sparkle, Metallic Red Sparkle, Metallic Royal Sparkle, Metallic Purple Sparkle, Metallic Green Sparkle

AVAILABLE SIZES: 1lb, 25 lbs, 100 lbs

Mix Ratio: Add 15% of X100 Nylon Bonding Agent to Excalibur® 500 Series direct printing inks.

Cleanup: 2000 Green or TR Blend Enviro Series washup.

AVAILABLE SIZES: 8oz (250mL), 16oz (500mL), Quart (1L)

TURN MOST CLEAR BASES INTO GLOW-IN-THE-DARK INKS!

Glow Powder pigments easily mix into most clear bases to form glow-in-the-dark inks. They are almost colorless by day, but glow yellow-green in the dark. Mix them to form fashion colors for daytime wear and startling luminous glows for night.

Mix Ratio: Add 10-25% glow pigment to ink base.

Cleanup: 2000 Green or TR Blend Enviro Series washup.

AVAILABLE SIZE: 1lb

TURN MOST CLEAR BASES INTO METALLIC GOLD INKS!

Use Metallic Gold Powder to create metallic gold screen printing inks. They easily disperse in any clear screen printing ink base, such as plastisol, vinyl, enamel, etc.

Ink Base & Mix Ratio: Use clear ink base. Add 4 oz. Metallic Gold Powder to a Litre/Quart of clear ink. Add 16 oz. Metallic Gold Powder to 4 Litres/Gallon clear ink.

Screen Mesh: All meshes up to 230 (92cm) mesh.

Mixing Instructions: Do not add powder directly to the ink as small lumps may form. Prepare a paste using the correct reducer for that ink type. Add the premixed paste to the ink and mix well.

AVAILABLE SIZE: 1 lb

TexTac is a new line of water based adhesive for tacking fabrics and T-shirts in place for screen printing. No more aerosol cans, environmental concerns solvents or fumes!

AVAILABLE SIZES: 1 Gallon, 5 Gallon

ADVANTAGES OF TEXTAC WATER-BASED ADHESIVE

High Production: Hundreds of shirts can usually be run without re-spray! A light re-application often will provide for another long production run. TexTac adhesive can be flash cured for rapid strength development and long holding power.

Water Soluble: The table/pallet can be cleaned with warm water!

No Disposability Problems: All adhesive can be fully used in application equipment. No flammable aerosol canister to store or to present a hazardous material disposal problem. TexTac contains no solvents, ammonia or mineral oil.

TW1000 Multi Plastic Ink offers excellent adhesion to a wide variety of substances without using a catalyst or a two part system. TW1000 Multi Plastic Inks are almost universal in their application to materials such as tennis balls, fabrics, leather, wood, metal, plastic bottles and sheeting, Tyvec®, etc. TW1000 Multi Plastic Inks have a semi-gloss finish with great durability and flexibility. TW1000 Multi Plastic Inks are exceptionally resistant to soaps and chemicals.

Excellent printing results can be obtained on most nylon materials. For hard to print nylon, pre-treat the printing area with acetone to remove some of the water-proofing agent. Pre-testing is always recommended before starting a screen printing job. For maximum adhesion and performance on synthetic fabrics, TW1000 Multi Plastic Ink must be thinned to penetrate the substrate.

AVAILABLE ACCESSORIES: TW-1073 Thinner, TW-1091 Retarder, L-1087 Washup

AVAILABLE COLORS: Clear, White, Black, Fire Red, Light Yellow, Primrose Yellow, Rampo Blue, Royal Blue, Emerald Green, Violet, Thinner, Retarder